[Quidway]display version ；显示版本信息
[Quidway]display current-configuration ；显示当前配置
[Quidway]display interfaces ；显示接口信息
[Quidway]display ip route ；显示路由信息
[Quidway]sysname aabbcc ；更改主机名
[Quidway]super passwrod 123456 ；设置口令
[Quidway]interface serial0 ；进入接口
[Quidway-serial0]ip address <ip> <mask|mask_len> ；配置端口IP地址
[Quidway-serial0]undo shutdown ；激活端口
[Quidway]link-protocol hdlc ；绑定hdlc协议
[Quidway]user-interface vty 0 4
[Quidway-ui-vty0-4]authentication-mode password
[Quidway-ui-vty0-4]set authentication-mode password simple 222
[Quidway-ui-vty0-4]user privilege level 3
[Quidway-ui-vty0-4]quit
[Quidway]debugging hdlc all serial0 ；显示所有信息
[Quidway]debugging hdlc event serial0 ；调试事件信息
[Quidway]debugging hdlc packet serial0 ；显示包的信息
静态路由：
[Quidway]ip route-static <ip><mask>{interface number|nexthop}[value][reject|blackhole]
例如：
[Quidway]ip route-static 129.1.0.0 16 10.0.0.2
[Quidway]ip route-static 129.1.0.0 255.255.0.0 10.0.0.2
[Quidway]ip route-static 129.1.0.0 16 Serial 2
[Quidway]ip route-static 0.0.0.0 0.0.0.0 10.0.0.2
动态路由：
[Quidway]rip ；设置动态路由
[Quidway]rip work ；设置工作允许
[Quidway]rip input ；设置入口允许
[Quidway]rip output ；设置出口允许
route add 添加路由[Quidway-rip]network 1.0.0.0 ；设置交换路由网络
[Quidway-rip]network all ；设置与所有网络交换
[Quidway-rip]peer ip-address ；
[Quidway-rip]summary ；路由聚合
[Quidway]rip version 1 ；设置工作在版本1
[Quidway]rip version 2 multicast ；设版本2，多播方式
[Quidway-Ethernet0]rip split-horizon ；水平分隔
[Quidway]router id A.B.C.D ；配置路由器的ID
[Quidway]ospf enable ；启动OSPF协议
[Quidway-ospf]import-route direct ；引入直联路由
[Quidway-Serial0]ospf enable area <area_id> ；配置OSPF区域
标准访问列表命令格式如下：
acl <acl-number> [match-order config|auto] ；默认前者顺序匹配。
rule [normal|special]{permit|deny} [source source-addr source-wildcard|any]
例：
[Quidway]acl 10
[Quidway-acl-10]rule normal permit source 10.0.0.0 0.0.0.255
[Quidway-acl-10]rule normal deny source any
扩展访问控制列表配置命令
配置TCP/UDP协议的扩展访问列表：
rule {normal|special}{permit|deny}{tcp|udp}source {<ip wild>|any}destination <ip wild>|any}
[operate]
配置ICMP协议的扩展访问列表：
rule {normal|special}{permit|deny}icmp source {<ip wild>|any]destination {<ip wild>|any]
[icmp-code] [logging]
扩展访问控制列表操作符的含义
equal portnumber ；等于
greater-than portnumber ；大于
less-than portnumber ；小于
not-equal portnumber ；不等
range portnumber1 portnumber2 ；区间
扩展访问控制列表举例
[Quidway]acl 101
[Quidway-acl-101]rule deny souce any destination any
[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo
[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo-reply
[Quidway]acl 102
[Quidway-acl-102]rule permit ip source 10.0.0.1 0.0.0.0 destination 202.0.0.1 0.0.0.0
[Quidway-acl-102]rule deny ip source any destination any
[Quidway]acl 103
[Quidway-acl-103]rule permit tcp source any destination 10.0.0.1 0.0.0.0 destination-port equal ftp
[Quidway-acl-103]rule permit tcp source any destination 10.0.0.2 0.0.0.0 destination-port equal www
[Quidway]firewall enable
[Quidway]firewall default permit|deny
[Quidway]int e0
[Quidway-Ethernet0]firewall packet-filter 101 inbound|outbound
地址转换配置举例
[Quidway]firewall enable
[Quidway]firewall default permit
[Quidway]acl 101 ;内部指定主机可以进入e0
[Quidway-acl-101]rule deny ip source any destination any
[Quidway-acl-101]rule permit ip source 129.38.1.1 0 destination any
发表评论